资讯专栏INFORMATION COLUMN

基于STM32的实验室点灯大师

KunMinX / 1576人阅读

摘要:初始化引脚和基础设置利用宏定义定义引脚高或者低全部引脚为高原理图是低平点亮高电平灭利用宏定义设置时间关闭灯流水灯延时时间为的值先关闭全部灯循环流水灯


/* USER CODE BEGIN Header *//**  ******************************************************************************  * @file           : main.c  * @brief          : Main program body  ******************************************************************************  * @attention  *  * 

© Copyright (c) 2021 STMicroelectronics. * All rights reserved.

* * This software component is licensed by ST under BSD 3-Clause license, * the "License"; You may not use this file except in compliance with the * License. You may obtain a copy of the License at: * opensource.org/licenses/BSD-3-Clause * ****************************************************************************** */
/* USER CODE END Header *//* Includes ------------------------------------------------------------------*//**初始化引脚和32基础设置**/#include "main.h"#include "gpio.h"/* Private includes ----------------------------------------------------------*//* USER CODE BEGIN Includes *//**利用宏定义定义32引脚 高(on)或者低(off)**/#define led0on HAL_GPIO_WritePin(GPIOC,GPIO_PIN_0, GPIO_PIN_RESET)#define led1on HAL_GPIO_WritePin(GPIOC,GPIO_PIN_1, GPIO_PIN_RESET)#define led2on HAL_GPIO_WritePin(GPIOC,GPIO_PIN_2, GPIO_PIN_RESET)#define led3on HAL_GPIO_WritePin(GPIOC,GPIO_PIN_3, GPIO_PIN_RESET)#define led4on HAL_GPIO_WritePin(GPIOC,GPIO_PIN_4, GPIO_PIN_RESET)#define led5on HAL_GPIO_WritePin(GPIOC,GPIO_PIN_5, GPIO_PIN_RESET)#define led6on HAL_GPIO_WritePin(GPIOC,GPIO_PIN_6, GPIO_PIN_RESET)#define led7on HAL_GPIO_WritePin(GPIOC,GPIO_PIN_7, GPIO_PIN_RESET)#define led0off HAL_GPIO_WritePin(GPIOC,GPIO_PIN_0, GPIO_PIN_SET)#define led1off HAL_GPIO_WritePin(GPIOC,GPIO_PIN_1, GPIO_PIN_SET)#define led2off HAL_GPIO_WritePin(GPIOC,GPIO_PIN_2, GPIO_PIN_SET)#define led3off HAL_GPIO_WritePin(GPIOC,GPIO_PIN_3, GPIO_PIN_SET)#define led4off HAL_GPIO_WritePin(GPIOC,GPIO_PIN_4, GPIO_PIN_SET)#define led5off HAL_GPIO_WritePin(GPIOC,GPIO_PIN_5, GPIO_PIN_SET)#define led6off HAL_GPIO_WritePin(GPIOC,GPIO_PIN_6, GPIO_PIN_SET)#define led7off HAL_GPIO_WritePin(GPIOC,GPIO_PIN_7, GPIO_PIN_SET)#define ledaoff HAL_GPIO_WritePin(GPIOC,GPIO_PIN_All,GPIO_PIN_SET)//PC全部引脚为高(原理图是低平点亮 高电平灭)/**利用宏定义设置时间**/#define time 100void gd() //关闭灯{ledaoff;} void lsd() //流水灯{ led0on; HAL_Delay(time); //延时时间为time的值 led0off; HAL_Delay(time); led1on; HAL_Delay(time); led1off; HAL_Delay(time); led2on; HAL_Delay(time); led2off; HAL_Delay(time); led3on; HAL_Delay(time); led3off; HAL_Delay(time); led4on; HAL_Delay(time); led4off; HAL_Delay(time); led5on; HAL_Delay(time); led5off; HAL_Delay(time); led6on; HAL_Delay(time); led6off; HAL_Delay(time); led7on; HAL_Delay(time); led7off; HAL_Delay(time);}/* USER CODE END Includes *//* Private typedef -----------------------------------------------------------*//* USER CODE BEGIN PTD *//* USER CODE END PTD *//* Private define ------------------------------------------------------------*//* USER CODE BEGIN PD *//* USER CODE END PD *//* Private macro -------------------------------------------------------------*//* USER CODE BEGIN PM *//* USER CODE END PM *//* Private variables ---------------------------------------------------------*//* USER CODE BEGIN PV *//* USER CODE END PV *//* Private function prototypes -----------------------------------------------*/void SystemClock_Config(void);/* USER CODE BEGIN PFP *//* USER CODE END PFP *//* Private user code ---------------------------------------------------------*//* USER CODE BEGIN 0 *//* USER CODE END 0 *//** * @brief The application entry point. * @retval int */int main(void){ /* USER CODE BEGIN 1 */ /* USER CODE END 1 */ /* MCU Configuration--------------------------------------------------------*/ /* Reset of all peripherals, Initializes the Flash interface and the Systick. */ HAL_Init(); /* USER CODE BEGIN Init */ /* USER CODE END Init */ /* Configure the system clock */ SystemClock_Config(); /* USER CODE BEGIN SysInit */ /* USER CODE END SysInit */ /* Initialize all configured peripherals */ MX_GPIO_Init(); /* USER CODE BEGIN 2 */ gd(); //先关闭全部灯 /* USER CODE END 2 */ /* Infinite loop */ /* USER CODE BEGIN WHILE */ while (1) { lsd(); //循环流水灯 /* USER CODE END WHILE */ /* USER CODE BEGIN 3 */ } /* USER CODE END 3 */}/** * @brief System Clock Configuration * @retval None */void SystemClock_Config(void){ RCC_OscInitTypeDef RCC_OscInitStruct = {0}; RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; /** Initializes the RCC Oscillators according to the specified parameters * in the RCC_OscInitTypeDef structure. */ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; RCC_OscInitStruct.HSEState = RCC_HSE_ON; RCC_OscInitStruct.HSEPredivValue = RCC_HSE_PREDIV_DIV1; RCC_OscInitStruct.HSIState = RCC_HSI_ON; RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL9; if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) { Error_Handler(); } /** Initializes the CPU, AHB and APB buses clocks */ RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2; RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK) { Error_Handler(); }}/* USER CODE BEGIN 4 *//* USER CODE END 4 *//** * @brief This function is executed in case of error occurrence. * @retval None */void Error_Handler(void){ /* USER CODE BEGIN Error_Handler_Debug */ /* User can add his own implementation to report the HAL error return state */ __disable_irq(); while (1) { } /* USER CODE END Error_Handler_Debug */}#ifdef USE_FULL_ASSERT/** * @brief Reports the name of the source file and the source line number * where the assert_param error has occurred. * @param file: pointer to the source file name * @param line: assert_param error line source number * @retval None */void assert_failed(uint8_t *file, uint32_t line){ /* USER CODE BEGIN 6 */ /* User can add his own implementation to report the file name and line number, ex: printf("Wrong parameters value: file %s on line %d/r/n", file, line) */ /* USER CODE END 6 */}#endif /* USE_FULL_ASSERT *//************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

文章版权归作者所有,未经允许请勿转载,若此文章存在违规行为,您可以联系管理员删除。

转载请注明本文地址:https://www.ucloud.cn/yun/120926.html

相关文章

  • 基于MDK创建STM32汇编语言工程——上机实验一(9527)

    摘要:设置下面的项为和项为,用于设置支持的软硬件仿真。如有错误,请斧正。参考文献基于创建汇编语言工程并分析 文章目录 1新建工程2配置环境3测试代码4分析生成的H...

    joy968 评论0 收藏0
  • STM32入门学习经验总结

    摘要:严格地说,应该是模仿实验。为什么觉得无从下手,看资料没有头绪经验总结看资料需要计划耐心和速度这里所谓的资料包括书籍文档。建议有报销条件的同学自己设计一块板子学习。无法报销的同学,可以选购一款开发板学习。 STM32系列基于专为要求高性能、低成本、低功耗的嵌入式应用专门设计的ARMCortex...

    biaoxiaoduan 评论0 收藏0
  • 【嵌入式】利用FinSH控制台控制LED灯

    摘要:嵌入式利用控制台控制灯点灯程序点灯程序要求在控制台输入命令来控制板子上的三盏灯暗灭 【嵌入式】利用FinSH控制台控制LED灯 点灯程序 点灯程序 要求:在Fin...

    liukai90 评论0 收藏0
  • 基于STM32OLED屏显示AHT20采集温湿度数据

    摘要:三小结本次实验在实现了温湿度数据采集并通过串口显示和利用屏数据显示代码的基础上,完成屏显示采集的温湿度数据也并不复杂,其中,温湿度数据采集的过程使用的是模拟,屏的数据显示采用的是。 ...

    vincent_xyb 评论0 收藏0
  • 单片机入门指南

    摘要:单片机入门指南本文基于常神文章基础上将单片机入门部分进行细化尽可能细节做到可实施性先引用一下常神的文章首先假设大家已经对高中物理的电路部分有所了解。单片机,如,是一种根据程序控制引脚高低电平的可编程器件,有些场合又将这种行为称作嵌入式。 ...

    nevermind 评论0 收藏0

发表评论

0条评论

KunMinX

|高级讲师

TA的文章

阅读更多
最新活动
阅读需要支付1元查看
<